×
Home
Commercial
Portraits
Blog
Wall Art
About
Schedule a Shoot

How To Hang A Picture With Wire

Wall Decor


Nowadays, it is more than just fun to hang a picture on your walls using a creative mind. One of them is to use canvas and picture wire.

It is a simple method, and everyone can do it at home with an ordinary mind. You will need to insert a few nails and rings to insert the wire through the canvas.

To learn the proper procedure for “how to put picture wire on canvas,” read the full article. It is a step-by-step guide to teach you how to put picture wire on canvas.

Before proceeding to the main topic of the article, it is necessary to know what a picture wire is and what tools you require to put the wire on canvas. Let's go through the article to know what canvas wire is and what tools are to be used to insert picture wire on canvas.
See Also:
How To Hang a Picture with Wire
How To Hang Pictures Wall Decor Guide
How To Hang Two Pictures Side by Side
How To Use a Picture Hanging Kit
Art Wall Decor

What is a Canvas Wire?

It is a simple wire used to hang pictures or objects on walls. There are many types of these wires made of various materials.

These wires hold different weights. Some are very strong, and others are sophisticated. Likewise, some are rigid and some are flexible. These wires are coated to not hurt your hands or fingers.

Essential Supplies You Required

The required tools are listed below:

  • Two D-rings
  • 4 screws (No more than 5/8″ in length)/li>
  • Ruler or measuring tape
  • Wire – Gauge will depend on canvas weight.
  • Wire cutters
  • Screw driver or drill
  • Pencil
  • Step 1: Keep Your Essential Supply with You

    li> Pencil

  • Screwdriver
  • Leveler
  • Hammer
  • Wall protection pads
  • Measuring tape or ruler
  • Nails
  • Step-2: Marking of Wooden Frame for D-Ring Installation.

    Place your painting or picture frame face downward on a clean surface or leaned over a clean surface if it’s a larger canvas.

    Measure the length of the insides of the canvas frame using a scale. With a pencil, mark a point between 1/3 and ¼ of the way down to the length of the canvas. Mark as 1/3 of the length for lighter-weight frames and ¼ of length for heavy weight frames.

    It is worth mentioning that when you mark 1/3 of a large canvas, your picture will not hug the wall.

    If you like your picture to stick to the wall, it is mandatory to mark ¼ on the large canvas. It looks awkward, if it is hung too far from the wall.

    Step-3: Fixation of D-Ring Through Screws.

    Recheck that your marks are in the right place and that your canvas is not upside down.

    Now it is time to place the D-ring over the lines you marked on the sides of the frame, flat side down.

    Push your screw in gently and straight. Get satisfaction by double checking that your screw is adjusted correctly. If the screw is not at the right angle, it will cause a problem in hanging.

    Use the correct screwdriver and screw the screw down straight and gently. You may drill into the wooden sides of the frame if you are an expert.

    Repeat the same on both sides of the canvas frame and ensure your D-right has no movement while screwing it.

    Using the proper tools is mandatory to avoid damage to the head of the screw.

    Never overtighten a screw. It will damage the screw threads.

    An incorrect screwdriver and an over-tightened screw may damage the screw, so avoid both.

    When you have successfully finished, you may check it.

    Step-4: How to Loop the Wire Through D-Ring

    Now, loop the wire through the D-ring and bend it. (you may loop 2-3 inches of wire)

    If your string (wire) is lighter, you should tie a tight knot with a wire. You may use a plier to tighten the knot more professionally. You can use pliers with lighter-weight string only. When using heavy wires, you may not use a plier.

    Step-5: How to Prepare Wire to Hang Frame on wall.

    Pull the wire under tension to the center of the upper frame while fully extending it.

    The wire should be around 1 cm below the upper frame when it is fully tensioned or hanging from the wall. If you're too close, it's challenging to hang out.

    The frame could stick too far from the wall if the height is too low.

    Cut it out with a 2-3-inch overlap at the end when it is at full tension.

    Always cut the wire longer than required.

    Step-6: Wire Wrap-Up to finalize the Procedure.

    If you are using heavy wire, you must wrap it up now. must wrap tightly around itself and reach to the end. It needs some practice to make it professionally neat and clean.

    It will help to keep the perpetual tension on the wire.You may use pliers to squeeze the wire from the ends when the wrapping of the wire is completed.

    Ensure the ends of the wire are fully secured. Never leave any sharp bits anywhere on the wire. Once, run your fingers up and down the wire to ensure it is smooth and does not have sharp bits.

    Step-7: To Put Bumpers on the Lower Corners the Canvas Frame.

    It is the final step. Now it is time to put frame bumpers on the lower corners of the canvas so that it may not damage your wall.

    Aww! Your canvas frame is ready to stick to the wall.

    Conclusion.

    Remember, there are many sizes and styles of canvas printing. The mechanism used to tack a canvas mostly depends on its size and style. For instance, you can hang a small canvas on the wall using a nail with a sawtooth bracket on the top of the rail of the frame.

    When using a large canvas, you must use wire on the sides of the frame to hang it properly.

    An ordinary string may be used to hang small, but when it comes to large canvas hanging, you need a strong wire with more endurance and stability to hold the heavy weight of the big canvas.

    Email Contact: [email protected]

    Milwaukee WI, US 53211

    Privacy Policy and Cookies